Help for equada® HostedPBX
1. Setup guide
This setup guide describes how to put a Behnke Station into operation as a SIP subscriber on an equada® HostedPBX cloud system. In the following, we assume that the basic configuration of the equada® HostedPBX cloud system has already been carried out, and we limit ourselves exclusively to the steps required to put the Behnke Station into operation.
It is assumed that the Behnke-Station is already set up to the extent that access to the web interface is possible. If this is not the case, please follow the instructions provided with your base electronics (manuals) and refer to the technical manualRecently updated — within the last 72 hours to complete the basic setup.
1.1. Setting up the subscriber for the Behnke Station
The following section contains only the steps required to create a user. The setup may differ in your installation. If in doubt, please contact your PBX support.
- Open the equada® management console in your browser.
- Log in with your administrator account.
- In the left-hand menu bar, click Registrierungen (Registrations).
- Select the Teilnehmer (Subscribers) tab.
- For the option Benutzerstatus (User status), select the value Alle (All).
- Click OK to save the configuration.
- In the lower area of the page, select the Übersicht (Overview) tab.
- A list of all subscribers that have been created should be displayed there.
- Click the number of the subscriber you have designated for the Behnke Station.
- In the left-hand menu bar, click Generisches Telefon (Generic phone).
- In the input field Name des Telefons (Phone name), you can assign a name.
- Tick the checkbox Automatisch generierter SIP-Benutzer (Automatically generated SIP user).
- Click the Hinzufügen (Add) button.
- If the entry is successful, you will receive a confirmation and an overview with the SIP credentials.
- Make a note of these SIP credentials, as you will need them later for configuring the Behnke Station.
1.2. Configuring the Behnke Station
- Open your browser
- Access the Behnke Station web interface
- Log in
- Click the
- Navigate to the SIP Account 1 or SIP Account 2 section.
- Set the Register option to yes
- Use the assignments from the following table and enter the information in the corresponding input fields (in the SIP Account 1 section, if applicable SIP Account 2) of your Behnke station.
- Open your browser
- Go to the web interface of the Behnke Station
- Log in
| Behnke Station field | equada® HostedPBX value |
|---|---|
| Phone number/user name | Phone number |
| User ID | SIP user |
| Password | Password |
| Communication | Specify SIP registrar and SIP proxy |
| Registrar | SIP domain |
| Port | 5082 |
| Proxy | sip.cloud-pbx.de |
| Port | 5082 |
- Click in the sidebar to save the configuration
- Wait a moment until the Behnke Station is reachable again
- If the registration is successful, the Registration state option changes to the value registered
- If this is not the case, please check the previous steps again
- Click the menu item in the sidebar to save the configuration
- Navigate to the section of the button to be configured, e.g. Button 1
- Set the Action option to the value Call
- In the input field of the Phone number option, enter the number that should be called when the button is pressed
- Click in the sidebar to save the configuration
The configuration of the Behnke Station was last updated for version 5.26.
2. FAQ
Note
There is currently no content available here yet. As soon as content is planned, the pages will be marked as planned. Feel free to use the Report a problem function on the right in the toolbar to request new content, ask questions, or report anything that is unclear.
You can also give feedback after every heading, so that we can continuously improve our wiki:
- Move your mouse over the heading
- A small ? appears
- Click the small ?
We welcome every suggestion, every correction and every idea for improvement.