Help for Auerswald® COMpact 5010 VoIP
1. Setup guide
This setup guide describes how to put a Behnke Station into operation as a SIP subscriber on an Auerswald® COMpact 5010 VoIP telephone system. In the following, it is assumed that the basic configuration of the Auerswald® COMpact 5010 VoIP telephone system has already been carried out, and we limit ourselves exclusively to the steps required to put the Behnke Station into operation.
It is assumed that the Behnke-Station is already set up to the extent that access to the web interface is possible. If this is not the case, please follow the instructions provided with your base electronics (manuals) and refer to the technical manualRecently updated — within the last 72 hours to complete the basic setup.
1.1. Setting up the subscriber for the Behnke Station
The following section contains only the steps required to create a user. The setup may differ in your installation. If in doubt, please contact your PBX support.
- First, open the management console of the Auerswald® system in your browser.
- Log in with your administrator access.
- In the sidebar, click the menu item COMset.
- In the expanded submenu, click Interne Rufnummern (Internal numbers).
- In the expanded submenu, click Teilnehmer (Tn) (Subscribers).
- In the expanded submenu, click Rufnummern (Numbers).
- Switch to the VoIP-Teilnehmer (VoIP subscribers) tab.
- In the Rufnummer (Number) column, in the Von (From) input field, specify the extension of the Behnke Station.
- In the Name column, enter a name for the Behnke Station.
- Make a note of the number and the name, as we need this information to configure the Behnke Station.
- Select the value Standard-VoIP-Telefon (Standard VoIP phone) as the device type.
- Click Übernehmen => Ausführen (Apply => Execute)
- In the sidebar, click the menu item Administration
- In the expanded submenu, click Benutzer-PIns/Passwörter (User PINs/passwords)
- Make a note of the password of the newly created user, as it is needed to configure the Behnke Station. If necessary, you can also change this password here.
1.2. Configuring the Behnke Station
- Open your browser
- Access the Behnke Station web interface
- Log in
- Click the
- Navigate to the SIP Account 1 or SIP Account 2 section.
- Set the Register option to yes
- Use the assignments from the following table and enter the information in the corresponding input fields (in the SIP Account 1 section, if applicable SIP Account 2) of your Behnke station.
- Open your browser
- Go to the web interface of the Behnke Station
- Log in
| Behnke Station field | Auerswald® COMpact 5010 VoIP value |
|---|---|
| Phone number/user name | Extension |
| User ID | Extension |
| Password | Password |
| Server | IP address of your COMpact 5010 |
- Click in the sidebar to save the configuration
- Wait a moment until the Behnke Station is reachable again
- If the registration is successful, the Registration state option changes to the value registered
- If this is not the case, please check the previous steps again
- Click the menu item in the sidebar to save the configuration
- Navigate to the section of the button to be configured, e.g. Button 1
- Set the Action option to the value Call
- In the input field of the Phone number option, enter the number that should be called when the button is pressed
- Click in the sidebar to save the configuration
The configuration of the Behnke Station was last updated for version 5.26.
2. FAQ
Note
There is currently no content available here yet. As soon as content is planned, the pages will be marked as planned. Feel free to use the Report a problem function on the right in the toolbar to request new content, ask questions, or report anything that is unclear.
You can also give feedback after every heading, so that we can continuously improve our wiki:
- Move your mouse over the heading
- A small ? appears
- Click the small ?
We welcome every suggestion, every correction and every idea for improvement.